Office furniture maintenance
Service · Office furniture maintenance
Keeping clean, checking over and adjusting, and replacing parts instead of the whole piece. What you can do yourself, and what you hand over to us.
Maintenance is keeping clean, checking over and replacing
Office furniture lasts for years, and with maintenance it lasts longer than the warranty period. It falls into three things. Keeping clean is the simplest and yields the most: wiping down with a damp cloth, vacuuming upholstery and clearing out castors. Checking over and adjusting is about bolts, levelling feet and the columns of a sit-stand desk — things that go out of true after use. Replacing is the work that involves tools and parts: a gas lift, a mechanism, a lock, a top or a base.
The first you do yourself or your cleaning service does. For the second and third you can call in our service department, and for the annual cleaning of carpet and upholstery we can schedule a round for you. That is usually a fraction of what replacement costs, and you keep an interior that goes on looking well cared for.
The places that wear
Eight places where maintenance yields something — and where leaving it out shows up first.








Four things we do for you
Maintenance you would rather not organise yourself we take off your hands. Request a proposal for your number of workstations.
What each of the three involves
The three parts of maintenance, set out. The first you do yourself or your cleaning service does; for the second and the third you can call us in.

Keeping clean: wiping down and vacuuming
Wipe tops, cabinets and frames with a damp cloth and a mild soapy solution — damp, not wet, and dry afterwards. Stay away from abrasives, glass cleaner and alcohol: they create matt patches and attack the top layer. Vacuum seats and backrests with a soft nozzle instead of scrubbing them. Tilt every chair and clear out the castors: hair and fluff wind themselves round the axles and make rolling heavy. Check at the same time whether the armrests are still tight.

Checking over and adjusting
Screwed joints settle on new furniture: tighten the bolts under the seat and of the backrest, adjust the levelling feet of cabinets until doors and drawers run free again, and clear the columns of the sit-stand desks of sand and crumbs. Do also actually adjust an electric desk: a motor that moves keeps going better than one that stands still. Would you rather not do it yourself? Our fitters go along the furniture and set the workstations to the user again.

Replacing the part, not the piece
A chair that slowly sinks has a worn gas lift, it does not need to be a new chair. The same goes for a mechanism, a set of castors or a lock. With desks the whole piece rarely has to go: if a top is damaged or has swollen, often only a new top can go on it, and if the base is faulty, we replace only the base and the top stays. Send a photo and the item number, and we will say whether there is a part for it and what it costs. If a piece really is due for replacement, look at refurbished first.
What you watch for
Office chairs
Check the bolts under the seat and of the backrest, and whether the armrests are still tight. If the chair slowly sinks or no longer comes up, the gas lift is at its end — that is a part, not a new chair.
Castors and base
Hair, dust and fluff wind themselves round the axles and make rolling heavy. Tilt the chair and clear out the castors; on hard floors soft castors also prevent scratches.
Sit-stand desks
Keep the columns clean and clear: sand and crumbs in the profile cause wear over time. Do also adjust the desk regularly — a motor that moves lasts better than one that stands still.
Cabinets and pedestals
Adjust the levelling feet if a door no longer closes or a drawer catches — that is almost always the cause, not the runner. Keep locks and keys together and note down the key numbers.
Upholstery and mesh
Vacuuming with a soft nozzle keeps dust out of the fibre; that is most of the work already. Do not scrub mesh backrests but vacuum them — rubbing stretches the weave. Having them professionally cleaned once a year keeps the upholstery good for longer; we can schedule that round for you.
Tops and veneer
Melamine and HPL can take a damp cloth with a mild soapy solution. Veneer and lacquered wood cannot: wipe them barely damp and dry them immediately afterwards. Keep moisture away from the edges, because that is where swelling starts. If a top is damaged or has swollen after all, often only a new top is needed.
Wearing parts and aids
What makes maintenance easier, and what is available if replacement is better than repair after all.
Active floor matBNR · floor protection
Cable wrapBNR · cable management
Flexy cable trayBNR · cable management
Ergo footrestBNR · ergonomics
BN410 document holderDataflex · ergonomics
Office chair FTS-II refurbishedBNR · refurbished
Office chair FTS-IIBNR · office chairs
Office chair Therapod XBNR · office chairs
Four rules that solve almost everything
Being quick makes the most difference
Dabbing a fresh stain with a dry, white cloth takes the greater part of it away. Dried in, it is a good deal harder.
Dab, do not rub
Rubbing pushes the stain into the fibre and creates a shiny patch. Work from the outside inwards so that no ring is formed.
On an inconspicuous spot first
Test every product on the back or the underside. Stay away from bleach, acetone and aggressive degreasers — they draw colour out of the fabric.
Follow the manufacturer's advice
Every fabric group has its own cleaning code. If that is no longer with the piece, ask us — we will look it up in the item data.
This is also about
Would you like to hand maintenance over, or are you unsure whether something can be repaired? Send a photo and the item number, or request a proposal for an annual maintenance round for your number of workstations.


Service & maintenance →
Working ergonomically →
Outlet and refurbished →